10mm To 8mm
-
Amana Tool 47722 Metric Steel Ball Bearing Guide 26mm Overall D x 10mm Inner D x 8mm Height
Bearings are double steel-shielded for extra rigidity and to inhibit dust. A special high-performance, high temperature grease is used for maximum life. Note: solvents should not be used to clean ball bearings. If a ball bearing becomes frozen (does not rotate freely) replace immediately.
$9.25$6.90 -
Amana Tool RB-110 High Precision Steel Router Collet Reducer 10mm Overall D x 8mm Inner D x 1 Inch Long
…high precision machined collet reduction sleeves enable collet sizes to be reduced to accept CNC and router bits with smaller shank sizes. Reduction sleeves are produced with high quality steel and precisely machined to limit the chance of run-out. Reducing the sleeve is not a long term solution,…
$9.25$6.90 -
Amana Tool 202008 Carbide Tipped Brad Point Boring Bit R/H 8mm D x 77mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$31.45$22.00 -
Amana Tool 302008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 77mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$31.45$22.00Related Products: 8mm X 77mm -
Amana Tool 201008 Carbide Tipped Brad Point Boring Bit R/H 8mm D x 57mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$22.80$15.95 -
Amana Tool 301008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 57mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$22.80$15.95Related Products: 8mm -
Amana Tool 204008 Carbide Tipped Brad Point Boring Bit R/H 8mm D x 70mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$24.00$16.80Related Products: 8mm Bits -
Amana Tool 304008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 70mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$24.00$16.80 -
Amana Tool 313008 Carbide Tipped Through-Hole Boring Bit R/H 8mm D x 57mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$32.75$22.90 -
Amana Tool 413008 Carbide Tipped Through-Hole Boring Bit L/H 8mm D x 58mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$32.75$22.90 -
Amana Tool 314008 Carbide Tipped Through-Hole Boring Bit R/H 8mm D x 70mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$36.40$25.50 -
Amana Tool 414008 Carbide Tipped Through-Hole Boring Bit L/H 8mm D x 70mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$36.40$25.50 -
Amana Tool 315008 Carbide Tipped Through-Hole Boring Bit R/H 8mm D x 77mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$41.55$29.10 -
Amana Tool 415008 Carbide Tipped Through-Hole Boring Bit L/H 8mm D x 77mm Long x 10mm SHK
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$41.55$29.10 -
Amana Tool 206008 Carbide Tipped Brad Point Boring Bit R/H 8mm D x 70mm Long x 10mm SHK High Performance Ditec
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$29.50$20.65 -
Amana Tool 305008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 57mm Long x 10mm SHK High Performance Ditec
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$26.50$18.55 -
Amana Tool 306008 Carbide Tipped Brad Point Boring Bit L/H 8mm D x 70mm Long x 10mm SHK High Performance Ditec
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$29.50$20.65 -
Amana Tool 316008 Carbide Tipped Countersink R/H 18mm D x 16.5mm Long x 8mm SHK
Use with 10mm shank boring bits to drill & countersink for screws in one pass.
$35.70$25.00 -
Amana Tool 416008 Carbide Tipped Countersink L/H 18mm D x 16.5mm Long x 8mm SHK
Use with 10mm shank boring bits to drill & countersink for screws in one pass.
$35.70$25.00 -
Amana Tool 365058 Reducing Bushing 10mm SHK for 8.0mm Drill
Use with solid carbide drills. Economic alternative to drill adapters. (Can be used on left or right hand drills).
$16.65$11.65 -
Amana Tool HBM-102 3-Pc Hinge Boring 57 Long x 10mm SHK Carbide Tipped Bit Set Includes Two #301008 (8mm D) and One #203351 (35mm D).
…need to sand the coating off before use. Once the tool starts drilling, the coating is cleared off the needed cutting edge right away. Amana's coating is applied onto the bit at a temperature of 570 F. The coating reduces the friction between the chip and the body inside the flute and it helps to…
$95.65$71.75Related Products: Hinge Bit