Solid Carbide Flush Trim
-
Amana Tool 51200 Solid Carbide Panel Pilot Flush Trim 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$15.60$11.70Related Products: Laminate Trim Bits -
Amana Tool RC-1230 Insert Solid Carbide Flush Trim Template 3/4 D x 30mm CH x 1/2 Inch SHK w/ Upper Ball Bearing Router Bit
Insert Carbide Flush Trim Router Bits Insert carbide is the economical way to go. Each knife has two edges; saves down time. Great for applications such as: hard/softwood, MDF, solid surface, chip board and plywood. #RC-2400 is meant for difficult work, the knives are held with 3 screws.
$140.30$105.25Related Products: Amana Rc Flush -
Amana Tool RC-2400 Insert Solid Carbide Flush Trim Template 3/4 D x 50mm CH x 1/2 Inch SHK w/ Upper Ball Bearing Router Bit
Insert Carbide Flush Trim Router Bits Insert carbide is the economical way to go. Each knife has two edges; saves down time. Great for applications such as: hard/softwood, MDF, solid surface, chip board and plywood. #RC-2400 is meant for difficult work, the knives are held with 3 screws.
$163.55$122.70Related Products: Rc-2400 -
Amana Tool RC-1000 Insert Solid Carbide Flush Trim 3/4 D x 15/32 CH x 1/4 Inch SHK w/ Lower Ball Bearing Router Bit
Each throw-away knife in this flush trimming bit has multiple edges. Rotate the knife to expose a fresh cutting edge. Reduce downtime to a minimum! Insert knives can be replaced at any time, even mid-job, without changing the router setup. Industrial quality.
$103.95$78.00 -
Amana Tool RC-1004 Insert Solid Carbide Flush Trim 3/4 D x 30mm CH x 1/2 Inch SHK w/ Lower Ball Bearing Router Bit
Each throw-away knife in this flush trimming bit has multiple edges. Rotate the knife to expose a fresh cutting edge. Reduce downtime to a minimum! Insert knives can be replaced at any time, even mid-job, without changing the router setup. Industrial quality.
$125.35$94.00 -
Amana Tool RC-1006 Insert Solid Carbide Flush Trim 3/4 D x 50mm CH x 1/2 Inch SHK w/ Lower Ball Bearing Router Bit
Each throw-away knife in this flush trimming bit has multiple edges. Rotate the knife to expose a fresh cutting edge. Reduce downtime to a minimum! Insert knives can be replaced at any time, even mid-job, without changing the router setup. Industrial quality.
$176.75$132.60 -
Amana Tool RC-1007 Insert Solid Carbide Flush Trim 3/4 D x 50mm CH x 1/2 Inch SHK w/ Double Upper BB and One Lower BB Router Bit
Each throw-away knife in this flush trimming bit has multiple edges. Rotate the knife to expose a fresh cutting edge. Reduce downtime to a minimum! Insert knives can be replaced at any time, even mid-job, without changing the router setup. Industrial quality.
$176.75$132.60 -
Amana Tool 51420 Solid Carbide Aluminum Flush Trim Up-Cut 1/4 D x 1-1/4 Cut Length x 1/4 SHK x 3-5/16 Inch Long Router Bit
Aluminum Cutting, Solid Carbide Flush Trim Router Bits 2 Flute with ball bearing guide Industrial quality Features a special grade carbide to perform quality cuts in aluminumThese flush trim router bits are designed to eject chips UP for clean cuts in aluminum and Aluminum Composite…
$119.30$89.50 -
Amana Tool 51520 Solid Carbide Aluminum Flush Trim Down-Cut 1/4 D x 1-1/4 Cut Length x 1/4 SHK x 3-5/16 Inch Long Router Bit
Aluminum Cutting, Solid Carbide Flush Trim Router Bits 2 Flute with ball bearing guide Industrial quality Features a special grade carbide to perform quality cuts in aluminumThese flush trim router bits are designed to eject chips UP for clean cuts in aluminum and Aluminum Composite…
$119.30$89.50Related Products: Spiral Flush Trim -
Amana Tool 51422 Solid Carbide Aluminum Flush Trim Up-Cut 1/4 D x 1/2 Cut Length x 1/4 SHK x 2-1/2 Inch Long Router Bit
Aluminum Cutting, Solid Carbide Flush Trim Router Bits 2 Flute with ball bearing guide Industrial quality Features a special grade carbide to perform quality cuts in aluminumThese flush trim router bits are designed to eject chips UP for clean cuts in aluminum and Aluminum Composite…
$115.55$86.70 -
Amana Tool 51522 Solid Carbide Aluminum Flush Trim Down-Cut 1/4 D x 1/2 Cut Length x 1/4 SHK x 2-1/2 Inch Long Router Bit
Aluminum Cutting, Solid Carbide Flush Trim Router Bits 2 Flute with ball bearing guide Industrial quality Features a special grade carbide to perform quality cuts in aluminumThese flush trim router bits are designed to eject chips UP for clean cuts in aluminum and Aluminum Composite…
$115.55$86.70Related Products: Flush Trim Router Bit -
Amana Tool 51206 Solid Carbide Panel Pilot Flush Trim 1/4 D x 3/8 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$17.60$13.20Related Products: Laminate Trim Bits -
Timberline 195-10 Solid Carbide Panel Pilot Flush Trim 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$13.65$9.55 -
Amana Tool 51200XL Solid Carbide Panel Pilot Flush Trim 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit with AlTiN Coating
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$17.70$13.30Related Products: Laminate Bit -
Amana Tool RC-2000 Insert Solid Carbide Economy Insert Flush Trim 1/2 D x 5/16 CH x 1/4 Inch SHK w/ Lower Ball Bearing Router Bit
Unique tool featuring small, 2-sided carbide insert knives. The ideal router bit for both routers and hand-held laminate trimmers with 1/4" shank. New design breakthrough allows this bit to be almost the same price as a regular brazed bit.
$63.00$47.25 -
Amana Tool 57174 Solid Carbide (Brazed to Steel Shank) Flush Trim Compression 22mm D x 1-9/64 CH x 1/2 Inch SHK w/ Lower Ball Bearing Router Bit
Solid Carbide (Brazed to Steel Shank) 2 Flute with Upper Ball Bearing Spiral Flush Trim Compression #57174 Used for trimming laminate work or for template and pattern work. For template application, the bearing follows the template, while the cutting edge trims the workpiece. With the router…
$197.55$148.20Related Products: Compression -
Amana Tool 51201 Solid Carbide Double End Panel Pilot Flush Trim 1/4 D x 1/4 CH x 1/4 SHK x 2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$19.85$14.90Related Products: Flush Bit -
Amana Tool 57187 Carbide Tipped Flush Trim 3/4 D x 2 Inch CH x 1/2 SHK x 4-Flute Router Bit
… Superior geometric design Advanced grinding technology that improves the carbides' resistance to wear Super clean cutsOptional Delrin replacement bearing use #47709, for a smooth cut finish when trimming solid surface materials. Feed rate is reduced, but chipping is virtually eliminated.
$108.85$81.65 -
Amana Tool 57184 Carbide Tipped Super Flush Trim 3/4 D x 1 Inch CH x 1/2 SHK x 4-Flute Router Bit
… Superior geometric design Advanced grinding technology that improves the carbides' resistance to wear Super clean cutsOptional Delrin replacement bearing use #47709, for a smooth cut finish when trimming solid surface materials. Feed rate is reduced, but chipping is virtually eliminated.
$71.90$53.90 -
Amana Tool 57185 Carbide Tipped Super Flush Trim 3/4 D x 1-1/2 CH x 1/2 Inch SHK x 4-Flute Router Bit
… Superior geometric design Advanced grinding technology that improves the carbides' resistance to wear Super clean cutsOptional Delrin replacement bearing use #47709, for a smooth cut finish when trimming solid surface materials. Feed rate is reduced, but chipping is virtually eliminated.
$71.05$53.30 -
Amana Tool 57186 Carbide Tipped Super Flush Trim 3/4 D x 2 Inch CH x 1/2 SHK x 4-Flute Router Bit
… Superior geometric design Advanced grinding technology that improves the carbides' resistance to wear Super clean cutsOptional Delrin replacement bearing use #47709, for a smooth cut finish when trimming solid surface materials. Feed rate is reduced, but chipping is virtually eliminated.
$90.30$67.70 -
Amana Tool 47135 Carbide Tipped DownShear SuperTrim Flush Trim 3/4 D x 1 Inch CH x 1/2 SHK w/ Lower Ball Bearing Router Bit
Upshear and Downshear trim router bits for exceptional speed and super-fine finish. Great for solid surface material when used with optional #47709 Delrin bearing. Carbide tipped Industrial quality Furnished with steel bearing #47714 (#47709 bearing optional)Do not use downshear router bit…
$46.15$34.60 -
Amana Tool 51436 SC Spiral, Plastic Flush Trim 1/4 D x 3/4 CH x 1/4 SHK x 3 Inch Long Double BB Router Bit
2 Flute - Mirror Finish Up-Shear Industrial quality spiral router bit designed for trimming sheets of stack plastics and laminates in hand-fed applications. Double bearing provides smoother action around contour of the template. Cuts Coroplast (A soft plastic cardboard made with super soft, super…
$62.70$47.00 -
Amana Tool 51712 Solid Carbide Hole and Flush Cut 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Router Bit
This solid carbide bit is used where laminate is applied over precut openings in the substrait. In a continuous operation, bore through the laminate and cut the laminate out of the opening. The plunge point bores through the laminate to begin, and the integral pilot rides along the openings inside…
$20.50$15.40 -
Amana Tool 51714 Solid Carbide Hole and Flush Cut 1/4 D x 1/4 CH x 1/4 SHK x 3-3/8 Inch Long Router Bit
This solid carbide bit is used where laminate is applied over precut openings in the substrait. In a continuous operation, bore through the laminate and cut the laminate out of the opening. The plunge point bores through the laminate to begin, and the integral pilot rides along the openings inside…
$35.95$26.96 -
Amana Tool 51716 Solid Carbide Hole and Flush Cut 1/4 D x 1/4 CH x 1/4 SHK x 4-1/4 Inch Long Router Bit
This solid carbide bit is used where laminate is applied over precut openings in the substrait. In a continuous operation, bore through the laminate and cut the laminate out of the opening. The plunge point bores through the laminate to begin, and the integral pilot rides along the openings inside…
$41.55$31.20 -
Amana Tool 51204 SC Short/Flat Pilot for Dado Clean Out & Dado Cleaning Flush Trim 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$15.60$11.70 -
Amana Tool 57153 Carbide Tipped Sink and Trim with Ultra-Glide BB Guide Solid Surface 3/4 D x 1 Inch CH x 10 Deg x 1/2 SHK Router Bit
Trim a sink cutout flush with the bowl in stages using these over-hang and flush trim bits in tandem. The overhang bits are equipped with non-marring Ultra-Glide bearings that are tapered to match the slope of the bowls side. A first pass with the appropriate overhang bit cleans the cutout edge,…
$54.05$40.55 -
Amana Tool 57154 Carbide Tipped Sink and Trim with Ultra-Glide BB Guide Solid Surface 3/4 D x 1 Inch CH x 1/2 SHK Router Bit
Trim a sink cutout flush with the bowl in stages using these over-hang and flush trim bits in tandem. The overhang bits are equipped with non-marring Ultra-Glide bearings that are tapered to match the slope of the bowls side. A first pass with the appropriate overhang bit cleans the cutout edge,…
$54.05$40.55 -
Timberline 195-14 Solid Carbide Panel Pilot Bevel Trim 7 Degree x 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$13.65$9.55 -
Amana Tool 51202 Solid Carbide Panel Pilot Bevel Trim 7 Degree x 1/4 D x 1/4 CH x 1/4 SHK x 1-1/2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$15.60$11.70 -
Amana Tool 46297 Solid Carbide UltraTrim Spiral Trim 1/4 D x 1 CH x 1/4 SHK x 3 Inch Long w/ Double BB Down-Cut Router Bit
Spiral flush trim bit, #46196 is used for acrylic, wood and MDF up to a 1/4" thick, for getting into tight corners with a small radius and great for cleaning out your edges. #46197 is mainly used for acrylic, wood and MDF up to a 1/2" thickness. Industrial Quality Carbide Tipped
$93.55$70.20 -
Amana Tool 51432 Solid Carbide InVectra Aluminum Laminate Trim 1/4 D x 5/8 CH x 1/2 SHK x 3-1/4 Inch Long Router Bit
2 Flute - Solid CarbideThe industrys solution for trimming aluminum laminates! Recommended by Formica & ATI Engineered from an Amana-exclusive carbide grade designed specifically for cutting both aluminum laminates and wood-based substrate materials. InVectra Aluminum laminate trim router bits -…
$159.45$107.02 -
Amana Tool 51430 Solid Carbide InVectra Aluminum Laminate Trim 1/4 D x 5/8 CH x 1/4 SHK x 2-3/8 Inch Long Router Bit
2 Flute - Solid CarbideThe industrys solution for trimming aluminum laminates! Recommended by Formica & ATI Engineered from an Amana-exclusive carbide grade designed specifically for cutting both aluminum laminates and wood-based substrate materials. InVectra Aluminum laminate trim router bits -…
$94.05$59.43Related Products: Laminate Trim Bits -
Amana Tool 57155 Carbide Tipped Lansen Stainless Steel Edge Sink and Trim with Ultra-Glide BB Guide Solid Surface 49/64 D x 1-1/2 CH x 12 Deg x 1/2 Inch SHK Router Bit
Trim a sink cutout flush with the bowl in stages using these over-hang and flush trim bits in tandem. The overhang bits are equipped with non-marring Ultra-Glide bearings that are tapered to match the slope of the bowls side. A first pass with the appropriate overhang bit cleans the cutout edge,…
$71.65$53.70 -
Amana Tool 51203 Solid Carbide Double End Panel Pilot Bevel Trim 7 Degree x 1/4 D x 1/4 CH x 1/4 SHK x 2 Inch Long Single Flute Router Bit
The ideal laminate trimming bits for high-volume production! Solid carbide and integral pilot (no bearing to maintain) extend life of bit, slim configuration reduces vibration. Also known as "bullet router bit". Solid carbide Suitable for routers and trimmers #51204 has a short/flat pilot…
$21.40$16.05
